NEWS

Small single-arm V-type mixer 20L, 30L, 50L, laboratory powder and particle mixer

The V-type mixer series products are high-efficiency asymmetric mixers, which are suitable for the mixing of powder or granular materials in industries such as chemical engineering, food, medicine, feed, ceramics, and metallurgy. This machine has a reasonable and simple structure, operates in a closed manner, and is convenient for feeding and discharging (either manually or by vacuum). The cylinder is made of stainless steel, which is easy to clean. It is one of the basic equipment for enterprises.

The product principle of the small single-arm V-type mixer 20L, 30L, 50L, and laboratory powder and particle mixer

One end of this machine is equipped with a motor and a reducer. The power of the motor is transmitted to the reducer through a belt, and then the reducer transmits it to the V-shaped barrel through a coupling. Make the V-shaped drum operate continuously to drive the materials inside the drum to mix up and down, left and right.

The mixing cylinder of this machine has a unique structure, ensuring uniform mixing, high efficiency and no material accumulation. The whole machine has a simple structure and is easy to operate.

Performance structure

The VH series V-type mixer can vacuum suck materials and discharge through a sealed butterfly valve, enabling dust-free operation.

The V-type mixer is composed of two asymmetrical cylinders. Materials can flow in both longitudinal and transverse directions, and the uniformity of mixing can reach over 99%.

The cylinder of the V-type mixer is made of stainless steel plates, with polished inner and outer walls, which is clean, hygienic and does not accumulate materials, meeting GMP requirements.

The VH series V-type mixer is easy to operate, equipped with timing operation and can also be operated in point mode.

Product application

The V-type mixer is suitable for the mixing of powder and granular materials with good fluidity and small physical property differences, as well as materials with low mixing requirements but short mixing time. Due to the smooth flow of materials inside the mixer cylinder, the original shape of the materials will not be damaged. Therefore, the V-type mixer is also suitable for the mixing of granular materials that are easy to break and wear, or finer powder, block materials, and materials containing a certain amount of water It is used for mixing various materials and is widely applied in the pharmaceutical, chemical, food and other industries.

Usage and maintenance

The usage method of V-type mixer

First, open the feed port of the mixer and confirm whether the discharge port is closed. Then, put the specified amount of material into the V-shaped cylinder as per the process control requirements. After the feeding is completed, to prevent the material from flowing out during the mixing process, the feeding port should be closed and locked. Now it's time for the machine to work. Press the power button, press the button to start the mixer, and adjust the motor speed to the speed specified by the process for mixing. After the mixing material has reached the time specified by the process, the machine can be stopped by adjusting the motor speed button. When stopping, the discharge port of the mixer should be facing the ground directly, and the motor speed adjustment button should be set to 0 position. The V-type mixer will stop rotating and the power supply will be cut off. The first step is to discharge the material: Open the feeding port of the V-type mixer and use the specified container to load the material at the discharging port until all the material in the hopper is discharged.

There are still many points that we need to pay attention to during the installation and operation of the V-type mixer. This is beneficial for us to maintain the V-type mixer and extend its service life.

1. Installation: Place the machine steadily, install the machine feet, and level it to ensure smooth operation of the machine.

2. Before use, add oil to the parts that need it first, then perform no-load operation to check if all fasteners are loose, if the electrical system is normal, and if the mechanical system operates normally. If any abnormalities are found, carry out repairs and adjustments.

3. Turn the feeding port to the top, open the feeding cover to add materials. The amount of materials added must not exceed the specified volume. Then close the feeding cover tightly and start the machine to operate. If any abnormality is found during the operation, the machine must be stopped for inspection.

4. When changing varieties, the inside and outside of the hopper must be thoroughly rinsed clean.